Response Electronics CL6011B Specifikace Strana 113
- Strana / 170
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-35Controller Cards
Original — December 1991 UM4.6:CS6003
Step 17: Set the SVCE XFER TEST switch to CONT IN. The service
transfer display station goes blank and then the
DISCONNECT TRANSFER STATION indicator on the service
transfer station should light. If the ADJUST CONTROLLER
OUTPUT indicator on the service transfer display station
lights. Adjust the current source to obtain the proper
indication.
Step 18: Disconnect the current source and jumpers.
Step 19: Set the SVCE XFER TEST switch to CONT OUT. The service
transfer display station numerical display shows “__ __ __”
indicating it is ready for use. If not, the service transfer unit
requires repair.
Step 20: Disconnect the service transfer cable.
Step 21: Set the calibrator ON/OFF switch to OFF.
Step 22: Remove the service transfer card and service transfer display
station.
5.11 Type DH7010 Power Converter Card
The DH7010 Power Converter Card is used in the local traffic director,
network traffic director and the system interface units. This procedure
allows the user to calibrate the 5 volt dc output and test the reset and
relay outputs of the power converter card.
X00630–A
TP1
R14 Supervisory Adjustment
TP2
TP3
TP4
TP5
Figure 5-18. Type DH7010 Power Converter Card
5
- Using and Maintaining the 1
- Type CS6003 Calibrator 1
- Documentation Map 3
- Appendixes 8
- Contents 10
- Original — December 1991 10
- UM4.6:CS6003 10
- Section Tab Guide 11
- 1 Introduction 13
- 1.5 Related Documents 14
- 1.6 Manual Conventions 15
- 1-4 Introduction 16
- 2 Using the Calibrator 17
- 2.2.1 Cables 18
- 2.2.2 Front Panel 18
- Using the Calibrator 19
- 2.2.2.7 Breakout Terminals 20
- 2.2.2.11 Numerical Display 20
- 2.2.2.12 Family Switches 21
- 2.2.2.13 Group Mode Switches 21
- 2.2.2.14 CHK MOM Switch 21
- 2.2.2.15 CARD IDENT Switch 21
- 2.2.2.16 Mode Switches 21
- 2.2.2.17 Status Indicator 22
- 2.2.2.18 Data Switches 22
- 2.3 Operating the Calibrator 23
- 2.3.4.1 Lamp Test 24
- 2.3.4.2 Procedures 24
- ± 0.1% ± 1 count 25
- ± 0.002 Vdc 25
- ± 0.0005 mV 25
- ± 0.005 ohms 26
- ± 0.01 ohms 26
- 3 Card Removal, Cleaning, and 27
- Installation 27
- 3.3 Circuit Card Cleaning 28
- 3.4 Corrosion 29
- 4 Input and Output Card 31
- 4.1.1.2 Equipment Required 32
- 4.1.1.3 Calibration Procedure 32
- Input and Output Card 33
- (Isolated) 34
- X00606–A 35
- 4.1.3.1 Overview 39
- 4-10 Input and Output Card 40
- Figure 4-3. RTD Input Card 40
- R2, and R3 for the RTD card 40
- 4.1.3.2 Equipment Required 41
- 4.1.3.3 Calibration Procedure 41
- 1. Zero adjustment 43
- 2. Span adjustment 43
- 4.1.4.1 Overview 44
- 4-15Input and Output Cards 45
- 4.1.4.2 Equipment Required 46
- 4.1.4.3 Calibration Procedure 46
- Input Cards 48
- 4.1.5.1 Overview 49
- 4.1.5.2 Equipment Required 49
- 4.1.5.3 Calibration Procedure 50
- 4.1.6.1 Overview 50
- 4.1.6.2 Equipment Required 51
- 4.1.7.1 Overview 54
- 4.1.7.2 Equipment Required 54
- 4.1.7.3 Calibration Procedure 54
- Input and Output Cards 56
- X00613–A 57
- 4.1.8.2 Overview 60
- 4.1.8.3 Equipment Required 60
- 4.1.8.4 Calibration Procedure 60
- Current Output Cards 61
- 4.2.1.2 Equipment Required 62
- 4.2.1.3 Calibration Procedure 62
- 1. 0=OFF; 1=ON 64
- X00616–A 65
- REMOVE W1 FOR 65
- MOMENTARY OPTION 65
- 4.2.3.2 External Relay Panel 74
- 4.2.3.3 Switch Settings 74
- 4.2.3.4 Overview 74
- 4.2.3.5 Equipment Required 74
- 4.2.3.6 Calibration Procedure 75
- 4-48 Input and Output Cards 78
- 5 Controller Cards 79
- 5.1.1 MPU Card 80
- 5.1.2 Process I/O Card 83
- 5.2.1 MPU Card 85
- 5.2.1.2 Calibration Procedure 86
- 5.2.2 Process I/O Card 88
- 5.2.2.2 Calibration Procedure 89
- 5.3.1 Equipment Required 92
- 5.3.2 Calibration Procedure 92
- 5.4.1 Equipment Required 94
- 5.4.2 Calibration Procedure 95
- 5.5.1 Equipment Required 97
- 5.5.2 Calibration Procedure 97
- (with Dual Current Output) 99
- 5.6.2 Calibration Procedure 100
- ± 0.01 volts dc 101
- ± 0.02 volts dc. If not, the 101
- Manual Control Cards 102
- 5.7.2 Calibration Procedure 103
- 5.8.1 Equipment Required 104
- Conversion Card 105
- 5.9.2 Calibration Procedure 106
- Controller Cards 107
- ± 0.015 volts dc. If 108
- 5.10.1 Equipment Required 110
- 5.10.2 Calibration Procedure 110
- 5.10.3 Functional Test 111
- ± 0.08 volts 112
- 5.11.1 Equipment Required 114
- 5.11.2 Calibration Procedure 114
- 6 Data Highway Cards 115
- 6.1.2 Calibration Procedure 116
- ± 0.050 volts 117
- ± 0.002 volts dc 117
- ± 0.005 volts dc. If not 117
- Devices)(PN41B0985) 118
- 6.2.2 Calibration Procedure 119
- ± 0.010 volts 120
- ± 0.050 volts dc on the 120
- Appendix A 121
- Maintaining the Calibrator 121
- A.3 Lamp Test 122
- A.4 Fan and Filter 122
- Glossary 123
- DM6461, DM6462, DM6463, Using 159
- Document by Number 159
- UM4.6:CS6003, 1-1 159
- Reader’s Evaluation 167
- 1712 CENTRE CREEK DR 168
- AUSTIN TX 78754–9971 168
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce